Parts catalogue

Right-Hand Carrier Extender

The MTL 8020-CE-RH is a right-hand carrier extender for the PAC8000 I/O system, extending Railbus communication and system power across multiple carriers for scalable distributed control.

8021-CE-LH

Left-Hand Railbus Carrier Extender

The MTL 8021-CE-LH is a left-hand Railbus carrier extender for the PAC8000 I/O system, ensuring Railbus connectivity between I/O carriers.

8103-AI-TX-02

Analog Input ModuleMTL

8-Channel Analog Input Module

The MTL 8103-AI-TX-02 is an 8-channel analog input module for high-accuracy 4-20 mA current loop signal acquisition, supporting 2-wire and 4-wire transmitters in PAC8000 I/O systems. 16-bit resolution, +/-0.1% accuracy.

8109-DI-DC-01

Digital Input ModuleMTL

8-Channel Discrete Input Module

The MTL 8109-DI-DC-01 is an 8-channel discrete input module for high-speed digital signal acquisition in PAC8000 I/O systems, supporting isolated sinking inputs and pulse counting. 0-30 VDC, FM-approved for non-incendive field wiring.

Contact for wholesale

8121-DI-DC

Digital Input ModuleEaton MTL

16-Channel Digital Input Module

Eaton MTL / Emerson PAC8000 series 16-channel digital input module for 24 V field signals, supporting selectable input speeds and pulse counting, suitable for hazardous-area I/O systems.

8121-DI-DC-01

Digital Input ModuleMTL

16-Channel Discrete Input Module

The MTL 8121-DI-DC-01 is a 16-channel discrete input module for high-speed digital signal acquisition in PAC8000 I/O systems, supporting dry-contact source-type switches and pulse counting. 18-30 VDC, FM-approved for non-incendive field wiring.

8123-PL-QU

Pulse/High-Speed Counter ModuleMTL

2-Channel Pulse/Quadrature Input Module

The MTL 8123-PL-QU is a 2-channel pulse/quadrature input module for flow meters, proximity detectors and rotary encoders in PAC8000 systems. Frequency range 1 Hz to 50 kHz (12.5 kHz in quadrature mode).

8142-DO-DC-03

Digital Output ModuleMTL

16-Channel Digital Output Module

The MTL 8142-DO-DC-03 (Emerson) is a 16-channel digital output module delivering DC output signals to actuators, solenoids and relays in PAC8000 systems. Source output, 12-42 VDC, 3 ms switching, IP20.

8502-BI-DP

Communication ModuleMTL

Profibus-DP Bus Interface Module

The MTL 8502-BI-DP is a Profibus-DP bus interface module (BIM) linking an MTL8000 node to a Profibus-DP host LAN. Supports up to 24 I/O modules, HART pass-through, up to 6 Mbaud.

8602-FT-ST

Standard Field Terminal

The MTL 8602-FT-ST is a standard snap-on field terminal for the PAC8000 I/O system, providing direct field wiring connection to I/O modules. Rated for Class I Div 2 / Zone 2 areas.

8612-FT-NA

16-Channel Field Terminal

The MTL 8612-FT-NA is a 16-channel non-arcing field terminal for the PAC8000 I/O system with screw-clamp terminals, suitable for Class I Div 2 / Zone 2 hazardous areas.

8615-FT-4W

4-Wire Field Terminal

The MTL 8615-FT-4W is a 4-wire current-sinking field terminal for the PAC8000 I/O system with screw-clamp terminals, suitable for Zone 2 / Class I Div 2 areas.

8617-FT-NI

Non-Incendive Field Terminal

The MTL 8617-FT-NI is a non-incendive field terminal for PAC8000 16-channel digital input modules, enabling safe direct field wiring in Class I Div 2 / Zone 2 hazardous areas.

8709-CA-08

8-Slot I/O Carrier

The MTL 8709-CA-08 is an 8-slot I/O carrier for PAC8000 systems, providing mounting and interconnection for up to 8 I/O modules with module addresses 1-64. Dimensions 342 x 170 x 22 mm.

8709-CA-08-01

8-Slot I/O Carrier With Earth Bar

The MTL 8709-CA-08-01 is an 8-slot I/O carrier for PAC8000 with an isolated earth bar and extended addressing (1-64). Carrier material modified poly-phenylene oxide; dimensions 342 x 170 x 22 mm.

8913-PS-AC

Power SupplyMTL

AC Power Supply

An MTL 8913-PS-AC power supply for the PAC8000 I/O system.

BPHM64

BackplaneMTL

HART Backplane

The MTL BPHM64 is a backplane that hosts HART interface modules (1 x MTL4841 communications module, 4 x MTL4842 HART interface modules) for process automation systems. Max power 1.35W.

CPM16-AI3700L

Isolation BarrierMTL

Safety Barrier Baseplate

The MTL CPM16-AI3700L is a 16-channel analog input safety barrier baseplate for hazardous areas, providing galvanic isolation between intrinsically safe and hazardous circuits. ATEX/IECEx rated, left-hand terminal arrangement.

CPS16

ConnectorMTL

16-Way Backplane Screw-Clamp Connector

The MTL CPS16 is a 16-module backplane with safe-area screw-clamp connections, part of the MTL Intrinsic Safety IS isolator range. General-purpose bus powered; weight 419g.

CPY-C3-ADV151

BackplaneMTL

Termination Backplane For Centum VP MTL4500 Series

The MTL CPY-C3-ADV151 is a termination backplane for Honeywell Experion and Yokogawa Centum VP DCS systems, providing field-wiring interface for MTL4500 series isolators. 24 V DC supply.

CPY-C3-RAI141

BackplaneMTL

Interface Backplane

The MTL CPY-C3-RAI141 interface backplane (Eaton Crouse-Hinds MTL) integrates Yokogawa Centum VP and ProSafe-RS systems with MTL4500 backplane-mounted isolators. 16-channel analog input, 4-20 mA.

F802

Power Supply ModuleRelcom

Redundant Fieldbus Power System

A Relcom F802 redundant fieldbus power system module.

HMP-HM64

Communication ModuleMTL

HART Multiplexer Unit

The MTL HMP-HM64 (Eaton Crouse-Hinds) is a HART multiplexer backplane supporting 2 x MTL4850 or MTL4854 multiplexer modules and up to 64 HART channels. FSM assessed, CE compliant.

ICC312

Isolation BarrierMTL

Independently Powered Isolator

The MTL ICC312 transfers transmitter current to two separate isolated output circuits and provides Line Fault Detection (LFD). Input current range 0-20 mA, power supply 20-35V DC.

MTL3052

Isolation BarrierMTL

Digital Isolator

The MTL3052 is a single-channel fully-floating digital isolator for hazardous areas (Zone 0, IIC, T4-6). Signal bandwidth DC to 10 kHz, replaceable 50 mA fuse.

MTL4016

Interface ModuleMTL

Switch/Proximity Detector Interface Unit

The MTL4016 allows two switches or proximity detectors in a hazardous area to control two safe-area loads each. Dual relay output, double-pole on/off, 2 ms response, contact rating 10W.

MTL4511

Interface ModuleMTL

Switch/Proximity Detector Interface Safety Module

The MTL4511 is a 1-channel switch/proximity detector interface with line fault detection. Response time 10 ms, contact rating 10W/0.5A/35V dc, for Zone 0 IIC T6 hazardous areas.

MTL4516C

Interface ModuleMTL

Switch/Proximity Detector Interface

The MTL4516C is a 2-channel switch/proximity detector interface from Eaton's MTL 4500 series, enabling safe-area loads to be controlled by mechanical switches or NAMUR proximity detectors in hazardous areas. ATEX/IECEx/FM/CSA certified.

MTL4521

Relay Output ModuleMTL

Loop-Powered Solenoid/Alarm Driver

The MTL4521 is a loop-powered solenoid/alarm driver for hazardous areas (Zone 0, IIC, T4). Input 20-35V DC, current limit 48 mA, min output 13.6V at 48 mA.

MTL4544

Power SupplyMTL

Repeater Power Supply

The MTL4544 is a 2-channel repeater power supply from Eaton's MTL 4500 series, providing isolated power to hazardous-area transmitters and repeating the 4-20 mA signal with HART pass-through.

MTL4575

Signal ConverterMTL

Temperature Converter

The MTL4575 is a single-channel temperature converter accepting RTD (Pt100/500/1000, Cu, Ni), thermocouple (J, K, T, E, R, S, B, N, XK) and millivolt inputs from hazardous-area sources (Zone 0, IIC, T4-T6).

MTL4841

Communication ModuleMTL

Communications Module

The MTL4841 is a communications module with an RS485 2-wire multidrop host interface; up to 31 units per host station. Baud rates 1.2-38.4 kbaud, RS485 highway length up to 1 km, power consumption <1.0W.

MTL4850

Communication ModuleEaton MTL

HART Multiplexer Module

The MTL4850 is a HART multiplexer module providing a secure interface between HART field devices and asset management systems. Designed for functional safety applications (IEC 61508 SIL3), it offers 32 channels per module and supports up to 2016 HART devices via RS485 at 24 VDC.

MTL5046

Isolating Driver

The MTL5046 is a single-channel isolating driver from the MTL 5000 series. It accepts a 4 to 20 mA safe-area input (1 to 24 mA under/over-range) with a 500 Hz to 10 kHz digital signal bandwidth and operates from a 20 to 35 V DC supply.

MTL5074

Temperature Converter

The MTL5074 is a temperature converter that converts low-level DC signals from thermocouples or RTDs in hazardous areas into a 4-20 mA current signal for safe-area loads. Accuracy is +/-0.1% FS, operating range -20 C to +85 C, IP20 protection, DIN-rail mounting.

MTL5514

Interface ModuleEaton MTL

Switch/Proximity Detector Interface

The MTL5514 is a switch/proximity detector interface from the Eaton MTL 5000 series, providing galvanically isolated connection between hazardous-area mechanical switches or NAMUR proximity detectors and safe-area equipment.

MTL5516C

Interface ModuleEaton MTL

Switch/Proximity Detector Interface

The MTL5516C is a two-channel switch/proximity detector interface from the Eaton MTL 5500 series. It provides galvanically isolated connections for mechanical switches or NAMUR proximity detectors, supports 4-20 mA loops with HART pass-through, and is certified for hazardous-area use.

MTL5532

Isolation BarrierEaton MTL

Pulse Isolator

The MTL5532 is a single-channel, fully-floating pulse isolator from the MTL 5000 series. It accepts NAMUR switches/proximity detectors or 2- or 3-wire voltage/pulse transmitters in Zone 0 hazardous areas, with a relay alarm output rated 0.5 A at 35 V DC max.

MTL5541

Power SupplyEaton MTL

Repeater Power Supply

The MTL5541 is a repeater power supply from the Eaton MTL 5000 series, providing a fully-floating DC supply to energise a 2- or 3-wire 4/20 mA transmitter in a hazardous area and repeat the current to drive a safe-area load.

MTL5541S

Power SupplyEaton MTL

Repeater Power Supply

The MTL5541S is a single-channel isolator/repeater power supply from the MTL 5500 series with analog input and DIN-rail mounting. Signal range 0 to 24 mA, transmitter voltage 16.5 V at 20 mA, transfer accuracy better than 15 uA at 20 C.

MTL5544

Power SupplyEaton MTL

Repeater Power Supply

The MTL5544 is a 2-channel 4/20 mA repeater power supply supporting HART and 2- or 3-wire transmitters. It provides fully-floating DC supplies to energise two hazardous-area transmitters and repeats the currents to drive two safe-area loads with bi-directional digital communication.

MTL5546Y

Isolating Driver

The MTL5546Y is a single-channel isolating driver from the MTL 5000 series for driving an I/P converter in a hazardous area. Working range 4 to 20 mA with a 500 Hz to 10 kHz digital signal bandwidth.

MTL5575

Temperature Converter

The MTL5575 is a temperature converter from the MTL 5000 series accepting thermocouple (THC) or RTD inputs in hazardous areas and providing an isolated safe-area output.

MTL5581

Signal ConditionerEaton MTL

Signal Conditioner

The MTL5581 is a signal isolator/conditioner from the Eaton MTL 5500 series with a 0 to +/-5 mV input range, DIN-rail mounting and -20 C to +60 C operating range.

MTL831B

TransmitterEaton MTL

Analogue Multiplexer Transmitter

The MTL831B is an intrinsically safe analogue input transmitter for Zone 0 hazardous areas. It monitors up to 16 thermocouples or millivolt sources (max +/-60 mV) and up to 15 RTDs, with redundant data highways and loop power supplied via the data highway.

MTL831C

TransmitterEaton MTL

Analogue Multiplexer Transmitter

The MTL831C is an intrinsically safe analogue transmitter for Zone 0 hazardous areas. It monitors up to 16 inputs from thermocouples, millivolt sources, RTDs or potentiometers and transmits signal and power over a single shielded twisted-pair cable up to 2 km. Paired with the MTL838C receiver for Modbus output.

MTL838-HON

Analog Input ModuleEaton MTL

Analogue Multiplexer Receiver

The MTL838-HON is a multiplexer receiver designed to connect with one or two MTL831C analog transmitters, managing transmitter configuration and receiving measurement data from up to 32 sensors. Data is made available via Modbus or for the LLMUX1 system, with sensor failure detection and status reporting.

MTL838B

Analog Input ModuleEaton MTL

Analogue Multiplexer Receiver

The MTL838B is a safe-area multiplexer receiver for hazardous-area applications with dual redundant data highways and dual RS485 Modbus outputs. It provides status reporting and sensor failure detection; up to 31 MTL838B-MBF units can communicate with one Modbus master.