Parts catalogue

IC660BBS102

Genius Block I/O Module

GE Fanuc field-mounted Genius block I/O module for Series 90 Genius I/O systems. Provides 16 configurable input/output circuits, 24 VDC nominal, with optical isolation between field and logic circuits.

IC660BBS103

Genius I/O Block

GE Fanuc Genius I/O block providing input and output capability with electronic fusing and isolation. Rated 115 VAC / 125 VDC, 8 points, 2 A load current per point, isolation voltage 250 VAC/VDC, operating temperature 0 C to 60 C.

IC660BLC001

CableGE Fanuc

Genius I/O Bus Cable

GE Fanuc Genius I/O bus cable, Belden-manufactured shielded twisted pair, approx. 15 inches (38 cm) with factory-terminated Genius bus connectors. Used to interconnect I/O blocks and controllers in Genius I/O systems.

Contact for wholesale

IC660BLM508

Bus CouplerGE Fanuc

Genius Bus Terminator

GE Fanuc Genius bus terminator for Genius I/O networks.

IC660BPM500

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor for setup, monitoring, and configuration of Genius I/O systems.

IC660BRD020

Digital Output ModuleGE Fanuc

Genius 16-Circuit DC Discrete Source Block

GE Fanuc Genius I/O module with 16 output circuits, rated 18-56V DC (suitable for 24V and 48V DC systems), typical power draw 150mA, maximum 300mA.

IC660BRD024

Genius Modular Redundancy Source Output Block

12/24V DC Genius source output block with 32 discrete outputs, output current 0.5 to 1.0 amps per point, inrush current max 10.0 amps. Part of the Genius I/O system used in T-Output subsystems.

IC660BRD025

Digital Output ModuleGE Fanuc

Genius 12/24V DC Sinking Output Block

12/24V DC Genius sinking output block with 32 isolated discrete output points. Built-in feedback resistors and blocking diodes; designed for Genius Modular Redundancy (GMR) systems. Operating temperature 20 C to 60 C.

IC660CBB902

Communication ModuleGE Fanuc

Genius Bus Controller Module

GE Fanuc Genius bus controller module for Series 90 PLC systems.

IC660CBB902K

Genius Bus Controller Board

GE Fanuc Genius bus controller circuit board.

IC660EBA103

Genius I/O Block Electronics Assembly

GE Genius I/O electronics assembly module that pairs with the IC660TBA103 terminal base to form a 6-channel thermocouple input block. Rated 115 VAC, block-to-block isolation 1500 V, group-to-group isolation 300 V RMS.

IC660EBD020T

Genius I/O Electronics Assembly

GE Fanuc Genius I/O electronics assembly module.

IC660EBD022

Termination UnitGE Fanuc

Genius I/O Terminal Assembly Module

GE Genius I/O field wiring interface between the I/O block and field devices. Rated 24V DC, compatible with IC660BBD20 I/O modules, accepts spade or ring terminals (max width 0.27 inches). Includes diagnostics for open wire, no-load, overload, and short circuit.

IC660EBD024

Genius 32-Circuit Discrete Input/Output Block

GE Fanuc Genius discrete input/output block with 32 circuits configurable as inputs or outputs, input voltage range 12 to 24 VDC, supports both sourcing and sinking configurations. Operating temperature 0 C to 60 C.

IC660EBD025

Genius I/O Module

GE Fanuc Genius I/O block module.

IC660EBD110P1

Genius 16-Circuit Input Electronics Assembly

GE 16-circuit input-only electronics assembly module for Genius I/O systems. Nominal input voltage 115 VAC, range 93-132 VAC, frequency 47-63 Hz. Pairs with IC660TBD110 terminal base and IC660BBD110 block assembly.

IC660ELB906R

ControllerGE Fanuc

Genius Bus Controller

GE Fanuc Genius I/O bus controller module.

IC660ELB912

Micro Genius Network Interface Card

GE Fanuc Micro Genius network interface board designed as a daughterboard within a microprocessor system, enabling communication between the Micro Genius and a host CPU via shared RAM.

IC660ELB912J

Micro Genius Network Interface Card

GE Fanuc Micro Genius network interface card used as a daughterboard within PC Interface Modules (PCIM). Enables host systems to communicate with Genius I/O devices over a Genius LAN. Current consumption 1.0 A (single channel), 1.5 A (dual channel).

IC660ERD025B

Genius Sinking Output Electronics Assembly

GE Fanuc Genius I/O electronics assembly for the 32-circuit sinking output block.

IC660ERD025C1

Genius Sinking Output Electronics Assembly

GE Fanuc Genius I/O electronics assembly for the 32-circuit sinking output block. Pairs with IC660TBD025 terminal base; equivalent block assembly IC660BRD025.

IC660FP8900K

Genius Bus Controller Board

GE Fanuc Genius bus controller circuit board (functional package equivalent to IC660CBB902K).

IC660FP900K

Digital Output ModuleGE Fanuc

Genius Output Module Functional Package

GE Fanuc Genius output module functional package (equivalent to IC600BF929K).

IC660HHM501

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor (HHM), an interface device for setup, monitoring, and configuration of Genius I/O systems. LCD 4 lines x 16 characters, 20-key sealed membrane keypad, power 115-230 V AC, 47-63 Hz, up to 6 hours battery operation.

IC660HHM501L

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor for setup, monitoring, and configuration of Genius I/O systems.

IC660HHM501N

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor for setup, monitoring, and configuration of Genius I/O systems.

IC660HHM501R

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor for setup, monitoring, and configuration of Genius I/O systems.

IC660HHM502

Genius Hand-Held Monitor

GE Fanuc Genius hand-held monitor, a diagnostic tool for configuring, monitoring, and troubleshooting distributed Genius I/O directly at the equipment. Integrates with GE Series 90-70 PLC systems and Genius bus controllers. Operating temperature 0 C to 60 C; multi-language support.

IC660TBA024

Field Termination AssemblyGE Fanuc

Genius Terminal Assembly Block

GE Fanuc Genius I/O terminal assembly block.

IC660TBA024K

Field Termination AssemblyGE Fanuc

Genius Terminal Assembly Block

GE Fanuc Genius I/O terminal assembly block.

IC660TBD024M

Field Termination AssemblyGE Fanuc

Genius Terminal Assembly Block

GE Fanuc Genius I/O terminal assembly block.

IC670ALG230

Field Control Analog Input Module

GE Fanuc Field Control analog input module. Single-ended grouped input, power supply 18-30 V (24 V typical), digital resolution 12 bits typical, input current span 0.1 mA to 20 mA, isolation 1500 VAC for 1 minute. Input impedance 249.75 to 250.25 Ohms.

IC670ALG240

Field Control Current Analog Input Module

GE Fanuc Field Control 16-point analog current source input module. Sixteen single-ended channels configurable for 0-20 mA or 4-20 mA, 16-bit ADC resolution, supports ANSI Type 2 two-wire and three-wire transmitter wiring. External power 20-28 VDC.

IC670ALG310

Field Control Analog Output Module

GE Fanuc Field Control analog output module.

IC670ALG310-LA

Field Control Analog Output Module

GE Fanuc Field Control analog output module. 8 single-ended channels, power supply 18 to 30 VDC (24 V typical), output range -10.25V to +10.25V, magnitude data size 14 bits, isolation 1500 VAC peak for 1 minute. Update time 1.5 ms typical.

IC670ALG320

Field Control Analog Output Module

GE 4-point analog output module for Field Control systems. Output channels 4, signal types 0-20 mA, 4-20 mA, 0-10 VDC, 0-12.5 VDC, 12-bit resolution. External power 20-29 VDC, isolation 1500 VAC for 1 minute.

IC670ALG330

Field Control 8-Point Analog Current-Source Output Module

GE Fanuc Field Control module with eight single-ended analog output channels, each providing 0-20 mA output current. Built-in 16-bit DAC, digital resolution 0.3125 uA per count.

IC670ALG620

Field Control RTD Analog Input Module

GE Field Control RTD analog input module accepting 4 independent 3-wire and/or 4-wire RTDs (platinum, nickel, nickel/iron, or copper). Selectable resistance ranges 0-500 ohms and 0-3000 ohms. Module supplies excitation current for RTDs.

IC670ALG630

Field Control Thermocouple Analog Input Module

GE Field Control thermocouple analog input module accepting up to 8 independent thermocouple or millivolt inputs. Supports thermocouple types J, K, T, E, S, R, B, N, G, C and Platinel II. Configurable spans 19.5 mV to 625 mV, 15-bit plus sign resolution, with cold junction compensation.

IC670CHS001

Field Control Wiring Base

GE Fanuc Field Control I/O wiring base.

IC670CHS001E

Field Control Wiring Base

GE Fanuc Field Control I/O wiring base.

IC670CHS002

Field Control I/O Terminal Block

GE I/O terminal block for the Series 90-30 PLC / Field Control system. Mounting base for up to two I/O modules with backplane communication and user connection terminals. Three isolated terminal groups (A, B, E), max 10 A per terminal, hot-swap capable, DIN rail mountable.

IC670CHS101

Field Control I/O Terminal Block

GE solid-state connection platform for GE I/O modules, with 37 points for inputs or outputs and power for two GE Fanuc I/O modules. Terminal wiring AWG #14 to #22, terminal torque 4.5 lb-in, max 10 A on terminals, hot-swap compatible.

IC670CHS102A

Field Control I/O Terminal Block

GE Fanuc wiring-to-board interface for Field Control I/O modules, with 16 screw terminals for field input/output wiring. Operating temperature -25 C to 70 C; requires Bus Interface Unit version 2.1 or higher.

IC670GBI002

Bus CouplerGE Fanuc

Field Control Genius Bus Interface Unit

GE Field Control Genius bus interface unit. MTBF over 183,000 hours, nominal 24 VDC (range 18-30 VDC), power 16.8 W max at full load, output to I/O modules 6.5 VDC plus/minus 5%, AC frequency 47-63 Hz.

IC670GBI002J

Bus CouplerGE Fanuc

Field Control Genius Bus Interface Unit

GE Fanuc Field Control Genius bus interface unit.

IC670GBI102

Communication ModuleGE Fanuc

Field Control Genius Bus Interface Module

GE Field Control module bridging field control I/O modules and the Genius bus. Screw terminals for main and optional redundant buses, 9-pin D-shell ports for handheld programmers. Transmission speeds 153.6 / 76.8 / 38.4 Kbaud, DIN rail mount, operating temperature 0-55 C.