Parts catalogue

Serial Communication Module

Yokogawa NFLR121-S00 is a serial communication module for FCN autonomous controllers. RS-422/RS-485; up to 1.85 Mbps; 1 channel; transformer isolation; up to 1200 m transmission; D-sub 9-pin female connectors.

NFLR121-S50

Serial Communication Module

Yokogawa NFLR121-S50 is a serial communication module for the STARDOM series. RS-422/RS-485 (2 ports); multipoint communication; half- or full-duplex; start-stop synchronization.

NFLR121-S51

Serial Communication Module

Recognized manufacturer reference available for industrial supply enquiry.

NFLR121-SE0

Serial Communication Module

Recognized manufacturer reference available for industrial supply enquiry.

Contact for wholesale

NFPW441-50

Power Supply Module

Yokogawa NFPW441-50 is a power supply module for field devices and control systems. Input 100-120 V AC; output +5.1 V DC (7.8 A) and 24 V DC (4 A); hot-swappable; SYS and FLD LED indicators; operating 0 to 55 C.

NFPW442

Power Supply Module

Recognized manufacturer reference available for industrial supply enquiry.

NFPW442

Power Supply ModuleYokogawa

Power Supply Module

Yokogawa NFPW442 is an AC-input power supply module for STARDOM FCN systems, accepting 220-240 V AC and delivering regulated +5.1 V DC for CPU and bus logic, supporting redundant power configuration.

NFPW442-50

Power Supply Module

Yokogawa NFPW442-50 is a power supply module for the STARDOM series. Rated input 220-240 V AC (range 170-264 V AC); input frequency 47-66 Hz; max input current 0.7 A; overcurrent and overvoltage protection; dimensions 49.7 x 130 x 146.5 mm.

NFPW444-10

Power Supply ModuleYokogawa

Power Supply Module

Yokogawa NFPW444-10 is a 24 V DC-input power supply module for STARDOM FCN systems, converting 24 V DC to a regulated +5.1 V DC output for the FCN backplane, supporting redundant power configuration.

NFPW444-50

Power Supply Module

Yokogawa NFPW444-50 is a power supply module with 24 V DC input. Input range 21.6-31.2 V DC; rated output +5.1 V DC; output current 0-7.8 A; dimensions 14.65 x 4.97 x 13 cm; weight 0.6 kg.

NFSB100

Bus CouplerYokogawa

SB Bus Repeat Module

Yokogawa NFSB100 is an SB bus repeat module for STARDOM FCN systems, regenerating and extending the SB local bus (up to 8 m per line) to connect extension I/O units, with hot-swap and duplex support.

NFSB100-S00

Bus Repeater Module

Bus repeater module that extends the SB bus segment length and links FOUNDATION Fieldbus-enabled devices in Yokogawa FCN-100/FCN-500 control systems. Single channel with transformer isolation and transmission distance up to 1200 m.

NFSB100-S01

Bus Repeater Module

Bus repeater module for the Yokogawa SB bus, used to extend communication range between control modules.

NFSB100-S50

Bus Repeater Module

Bus repeater module that amplifies signals on the Yokogawa SB internal serial bus to extend communication range across larger control systems. Operating temperature -20 to +60 C.

NFSBT02

ControllerYokogawa

Modular Controller

FCN-500 series modular controller CPU module with ECC memory and fanless low-heat-dissipation design. Supports duplexing and hot-swappable modules for high reliability.

NFTA4S-00

Analog Input Terminal Block

Pressure clamp terminal block connecting analog field devices to FCN analog input modules. 16 independent channels, 4-20 mA / 1-5 V DC input, 16-bit resolution, accuracy +/-0.1% of full scale.

NFTA4S-10

Analog Input Terminal Block

Yokogawa Stardom-series pressure clamp terminal block converting analog sensor signals for a controller. 16 independent channels, 4-20 mA / 1-5 V DC input, 16-bit resolution, +/-0.1% accuracy.

NFTB5S-00

Pressure Clamp Terminal Block

Pressure clamp terminal block providing secure connections between pressure sensors and FCN autonomous controllers. DIN-rail mount, operating temperature -20 to 60 C.

NFTC5S-00

Temperature Input Terminal Block

Terminal block supporting thermocouple (K, J, T, R, S, B, N, W, L) and RTD (Pt100, JPt100) temperature inputs. Communication via RS485 Modbus RTU and Profibus DP-V1.

NFTI3S-00

Analog Input ModuleYokogawa

Analog Input Module

Analog input module connecting analog sensors to an FCN autonomous controller. 16 independent channels, 4-20 mA / 1-5 V DC input, 12-bit resolution, +/-0.2% accuracy.

NFTP01

Field Termination AssemblyABB

Field Termination Panel

ABB NFTP01 field termination panel for ABB control systems.

NFTP5S-00

Pressure Clamp Terminal Block

Pressure clamp terminal block for connecting field devices to FCN autonomous controller I/O modules. 32-channel digital I/O, 4-20 mA DC output, power supply 10.5 to 45 V DC.

NFTR85-10

Digital Input ModuleYokogawa

Digital Input Module

Digital input module with 32 channels, 24 VDC input, 7 mA per channel and channel-to-system isolation. Operating temperature -20 to +70 C.

NFTR8S-10

Analog Input ModuleYokogawa

Analog Input Module

Analog input module connecting RTD sensors to an FCN autonomous controller. 8 independent channels, temperature range -50 to +150 C, 12-bit resolution, +/-0.1% accuracy.

NFZ40E-21 1SBH136001R2140

ContactorABB

NFZ40E-21 Contactor Relay

ABB NFZ40E-21 NF-range contactor relay. AC/DC operated with electronic coil interface accepting a wide control voltage range. Z coil type allows direct 24 Vdc / 500 mA PLC output control with reduced holding consumption.

NGDR-02C

Gate Driver BoardABB

Gate Circuit Board

ABB NGDR-02C gate circuit board for ACS600 series inverters. Controls power flow to the AC motor. 24V DC, dimensions 120 x 80 x 35 mm.

NGDR-03C 58976539

Control BoardABB

Gate Circuit Card

ABB NGDR-03C gate driver circuit card, part 58976539.

NGDR-03C 61353364D

Gate Driver BoardABB

NGDR-03C Gate Driver Board

ABB NGDR-03C gate driver board that amplifies control pulses for IGBTs. 24V DC, dimensions 2 x 10.5 x 11 cm.

NGPS-11 61258523

Drive Power ModuleABB

NGPS-11 Power Board

ABB NGPS-11 power supply board for ABB automation platforms. Provides power distribution within control systems. Country of origin Switzerland.

NGPS-12C

Power SupplyABB

Power Supply Board

ABB NGPS-12C power supply board for industrial environments. Operating voltage 220V, output frequency 50 kHz, dimensions 135 x 186 x 119 mm. CE and UL certified.

NGPS-13C 3AUA0000042489

Power SupplyABB

NGPS-13C Power Supply Board

ABB NGPS-13C power supply options kit. Net weight 0.53 kg.

NI-9162

Carrier / Mounting BaseNational Instruments

cDAQ-9162 USB Carrier

National Instruments NI-9162 is a single-slot USB carrier for CompactDAQ C Series modules.

NI-9234

Analog Input ModuleNational Instruments

Sound and Vibration Input Module

National Instruments NI-9234 is a 4-channel C Series sound and vibration analog input module with IEPE support.

NI-9345

Counter ModuleNational Instruments

C Series Counter Module

National Instruments NI-9345 is a C Series counter input/output module for industrial counting and quadrature encoder applications.

NIAI03

Analog Input ModuleABB

Analog Input Termination Module

ABB Bailey NIAI03 analog input termination module for Infi 90 / Net 90 control systems.

NIAI04

Termination UnitABB Bailey

Analog Input Termination Unit

ABB Bailey INFI 90 analog input termination unit.

NIAI04

Analog Input Termination Module

ABB Bailey NIAI04 analog input termination module for Infi 90 / Net 90 control systems. Country of origin United States.

NIAI05

Analog Input ModuleABB

Analog Input Termination Module

ABB Bailey NIAI05 analog input termination module. Net weight 0.318 kg. Country of origin United States.

NICL01

Communication ModuleABB

Communication Termination Module

ABB Bailey Infi 90 NICL01 communication link termination module for process control systems. Rack-mounted.

NICS01

Controller Station Termination Unit

ABB Bailey NICS01 controller station termination unit for Infi 90 control systems.

NIDI01

Termination UnitABB Bailey

Digital I/O Termination Module

ABB Bailey INFI 90 / Network 90 digital I/O termination module.

NIDI01

Digital Input Termination Module

ABB NIDI01 digital input termination module for Infi 90 control systems. Country of origin United States.

NIMF01

Multifunction Termination Module

ABB NIMF01 multifunction termination module interfacing ABB controllers (INICT01, INPPT01, INPCT01) with external devices. Country of origin United States.

NIMF02

Redundant Multi-Function Controller Termination Module

ABB NIMF02 redundant multi-function controller termination module for ABB control systems.

NIMP01

Multi-Function Processor Termination Unit

ABB Bailey NIMP01 multi-function processor termination module for serial communication (RS-232-C, RS-485) in INFI-NET systems. Supports redundant configurations.

NIMP02

Processor Termination Module

ABB NIMP02 processor termination module used with NIMP01 for redundant multi-function processor setups. Serial communication via RS-232-C and RS-485.

NINP-61C

Surge ProtectorABB

Input Protection Card

ABB NINP-61C input protection card safeguarding input circuits against voltage surges. Input range 100V to 500V AC/DC, 8 input channels.

NINT-41C

Communication ModuleABB

Communication Board

ABB NINT-41C communication board supporting Ethernet/IP, Profinet and DeviceNet. 24V DC, dimensions 88 x 100 x 34 mm.