Parts catalogue

Analog Input Module

GE Fanuc Series 90-30 / PACSystems RX3i analog input module (revision G).

IC693ALG222

Analog Voltage Input Module

GE Fanuc Series 90-30 analog voltage input module. 16 single-ended or 8 differential channels, unipolar 0-10 V or bipolar -10 to +10 V, 1500 V RMS isolation. Module OK and Power Supply OK status LEDs.

IC693ALG223

Analog Current Input Module

GE Fanuc Series 90-30 analog current input module. 1 to 16 selectable single-ended channels, ranges 0-20 mA / 4-20 mA, 13 ms update for all 16 channels, 1500 V isolation.

IC693ALG223D

High Density Analog Input Module

GE Fanuc Series 90-30 high-density analog input module (revision D).

Contact for wholesale

IC693ALG390

Analog Output Module

GE Fanuc Series 90-30 analog output module.

IC693ALG390D

Analog Output Module

GE Fanuc Series 90-30 analog output module (revision D).

IC693ALG391

Analog Current Output Module

GE Fanuc Series 90-30 analog output module (current/voltage). 2 channels, ranges 1-5 V, 0-5 V, 0-20 mA, 4-20 mA. 12-bit resolution, 5 ms update, 1500 V RMS isolation, terminal block connector.

IC693ALG391F

Analog Output Module

GE Fanuc Series 90-30 analog current/voltage output module (revision F).

IC693ALG391G

Analog Current Output Module

GE Fanuc Series 90-30 analog current/voltage output module (revision G).

IC693ALG392

Analog Output Module

GE Fanuc (Emerson) analog output module for PACSystems RX3i and Series 90-30. High-density current/voltage output, 8 channels. Dimensions 13 x 3.5 x 14 cm.

IC693ALG392B

Analog Output Module

GE Fanuc Series 90-30 high-density analog output module (revision B).

IC693ALG392C

Analog Output Module

GE Fanuc Series 90-30 high-density analog output module (revision C).

IC693ALG442

Analog I/O ModuleGE Fanuc

Analog Current/Voltage Combination Module

GE Fanuc Series 90-30 / RX3i analog combination module. 4 differential analog inputs, 2 single-ended analog outputs. Voltage 0 to +10 V / -10 to +10 V, current 0-20 mA. 1500 VAC isolation, field-upgradeable firmware.

IC693ALG442CA

Analog I/O ModuleGE Fanuc

Analog Current/Voltage Combination Module

GE Fanuc Series 90-30 analog input/output combination module (revision CA).

IC693APU300

High Speed Counter Module

GE Fanuc Series 90-30 high-speed counter module. High frequency 80 kHz, low 20 Hz, positive logic, 12 fast inputs (5 VDC or 10-30 VDC), 4 fast outputs (10-30 VDC at 500 mA). 3 A fuse output protection.

IC693APU300E

High Speed Counter Module

GE Fanuc Series 90-30 high-speed counter module (revision E).

IC693APU300J

High Speed Counter Module

GE Fanuc Series 90-30 / PACSystems RX3i high-speed counter module (revision J).

IC693APU301

Axis Positioning Module

GE Fanuc Series 90-30 single-axis positioning module for servo motion control. Microprocessor-based, 1 ms servo loop update, 25-pin servo connection. Standard and follower operating modes. Compatible with CPU 311/313/323/331 and higher.

IC693APU301D

Axis Positioning Module

GE Fanuc Series 90-30 / PACSystems RX3i single-axis positioning module (revision D).

IC693APU301R

Axis Positioning Module

GE Fanuc Series 90-30 single-axis positioning module (revision R).

IC693APU302

Power Mate Axis Positioning Module

GE Fanuc Series 90-30 two-axis Power Mate Axis Positioning Module (APM). Controls two servo motors in standard or follower (electronic gearing) modes. Block processing under 5 ms, hot-swappable, mounts on any Series 90-30 baseplate.

IC693APU302F

Power Mate Axis Positioning Module

GE Fanuc Series 90-30 two-axis Power Mate Axis Positioning Module (revision F).

IC693APU330

High Speed Counter Module

GE Fanuc Series 90-30 high-speed counter module.

IC693BEM320

I/O Link Interface Module

GE Fanuc Series 90-30/90-70 solid-state I/O Link Interface Module (slave only). Up to 64 I/O points, 2 serial ports (RS-485 and RS-422), jumper-selectable 32 or 64 points.

IC693BEM330

Remote I/O ModuleGE Fanuc

Remote I/O Scanner Module

GE Series 90-30 Remote I/O Scanner Module. Factory Instrumentation Protocol (FIP), two 9-pin D-shell connectors, 1 MHz transmission, supports up to 19 I/O modules, mounts in slot 1 of the CPU baseplate.

IC693BEM331

Genius Bus Controller

GE Series 90-30 Genius Bus Controller. Interfaces a Genius I/O serial bus to a Series 90-30 PLC, transmitting up to 128 bytes for up to 31 devices on the Genius bus.

IC693BEM331J

Genius Bus Controller

GE Fanuc Series 90-30 Genius Bus Controller (revision J).

IC693BEM331K

Genius Bus Controller

GE Fanuc Series 90-30 Genius Bus Controller (revision K).

IC693BEM340

FIP Bus Controller

GE Fanuc Series 90-30 FIP Bus Controller. Single-slot module interfacing to a FIP I/O serial bus, two 9-pin male D connectors plus 15-pin RS-485 serial port, supports redundant FIP buses. 1.2 A max, six status LEDs.

IC693BEM341

FIP Bus Controller

GE Series 90-30 high-speed FIP Bus Controller. Two 9-pin D-shell FIP connectors (2.5 MHz) plus RS-485 port, redundancy support. Mounts in slot 1 of the CPU baseplate, max 1.2 A draw, CPU release 8.10 or higher.

IC693BEM341CD

FIP Bus Controller

GE Fanuc Series 90-30 high-speed FIP Bus Controller (revision CD).

IC693CHS391

10-Slot Modular CPU Expansion Baseplate

GE Fanuc Series 90-30 10-slot modular CPU baseplate. Houses CPU, I/O and power supply modules. +5 VDC bus, 25-pin female expansion connector, 9 I/O slots.

IC693CHS391EG

10-Slot Modular CPU Expansion Baseplate

GE Fanuc Series 90-30 10-slot modular CPU expansion baseplate (revision EG).

IC693CHS391N

10-Slot CPU Baseplate (EMI Enhanced)

GE Fanuc Series 90-30 10-slot CPU baseplate (revision N, EMI enhanced).

IC693CHS392

10-Slot Expansion Baseplate

GE Series 90-30 10-slot expansion backplane. Adds I/O capacity without an extra CPU. Hot-swap capable, panel mount, dimensions 443 x 142 x 130 mm, 150 mA at 5 VDC.

IC693CHS392J

10-Slot Expansion Baseplate

GE Fanuc Series 90-30 10-slot expansion baseplate (revision J).

IC693CHS393

Carrier / Mounting BaseGE Fanuc

10-Slot Remote I/O Baseplate

GE Series 90-30 10-slot remote I/O baseplate. Extends I/O up to 700 ft (213 m) from the CPU, dedicated power supply slot, 25-pin female D expansion connector, built-in ground isolation. 460 mA at 5 VDC.

IC693CHS393J

Carrier / Mounting BaseGE Fanuc

10-Slot Remote I/O Baseplate

GE Fanuc Series 90-30 10-slot remote I/O baseplate (revision J).

IC693CHS397

5-Slot Modular CPU Baseplate

GE Fanuc Series 90-30 5-slot modular CPU baseplate. Mounts CPU, power and expansion modules. Dimensions 12.3 x 7.9 x 4.7 in.

IC693CHS397E

5-Slot Modular CPU Baseplate

GE Fanuc Series 90-30 5-slot modular CPU baseplate (revision E).

IC693CHS397M

5-Slot Modular CPU Baseplate

GE Fanuc Series 90-30 5-slot modular CPU baseplate (revision M).

IC693CHS398

5-Slot Expansion Baseplate

GE Series 90-30 5-slot expansion baseplate. Adds I/O slots, DIN-rail installable, 5 VDC, 270 mA internal consumption. Max cable length 50 ft (15 m) between CPU and expansion baseplates.

IC693CHS398D

5-Slot Expansion Baseplate

GE Fanuc Series 90-30 5-slot expansion baseplate (revision D).

IC693CHS398F

5-Slot Expansion Baseplate

GE Fanuc Series 90-30 5-slot expansion baseplate (revision F).

IC693CHS398G

5-Slot Expansion Baseplate

GE Fanuc Series 90-30 5-slot expansion baseplate (revision G).

IC693CMM301

Communications Module

GE Fanuc Series 90-30 / PACSystems RX3i communications module.

IC693CMM302

Enhanced Genius Communications Module

GE Fanuc Series 90-30 Enhanced Genius Communications Module. Genius Global Data communications with up to 31 devices, <300 mA at +5 VDC, OK and COMM status LEDs.

IC693CMM302L

Enhanced Genius Communications Module

GE Fanuc Series 90-30 Enhanced Genius Communications Module (revision L).